Our Metrology laboratory operates under guidelines set forth in the NIST Handbook 150-2 (Aug 95) and ISO/IEC Guide 25 3rd edition ( It is equipped to calibrate thermocouples and RTD's using NIST traceable measuring and test equipment. Our equipment's useful range is from -40C to 1700C and includes cryogenic points of -195.64C and -56.42C. We also maintain the triple point of water.

MIL-STD-45662-A is used as a guide for all calibrations. Other references and standards used might include (but are not limited to) ASTM-563, E-77, E-207, E-220, E-230, E-601, IEC 584-1, 751 or ANSI/MC 96.1, JMS Southeast offers calibration services for standard thermocouples as well as non-standard thermocouples. Because of possible inhomogeneities along the length of the thermocouple, readings may vary from one furnace to the next. It is not recommended that a calibration be performed on used thermocouples, but we will calibrate your sensors based on the initial thermocouple tolerances. Since sensors do not have trim pots of microprocessors to adjust, our calibration reports consist of 'As Found Data'. However, if you would like for us to calibrate a sensor along with a transmitter, readout device, or controller which may have adjustable guts, we will be more than happy to adjust the instrument so that your system accuracy is documented.

Uncertainties (Webster): 1. indefinite 2. not certain to occur 3. not known beyond doubt

Error (Webster): The difference between an observed or calculated value; not a true value. The amount of deviation from a standard or specification.

Precision (Webster): The degree of refinement with which a measurement is stated.

ASTM: The scatter between individual values of test data within the subset. Normally computed with respect to the mean of the subset.

Bias (Webster): Deviation of the expected value of a statistical estimate from the quantity it estimates.

ASTM: The scatter between the mean values of subsets of data from each other and from the accepted value.

JMS Southeast - What we refer to as uncertainties fall under 2 categories:

1. Mathematical / statistical / or calculated uncertainties: Those interpolated or extrapolated numbers which are impossible to determine without more frequent measured points. These numbers are ) at the measured points, expandable between points and go out to infinity beyond the end points.

2. Measurement uncertainties: Those numbers derived at the measurement points which must be added to the total possible uncertainty of measurement. They include reference probe, instrument, probe under test and medium instabilities plus accuracy ratings of those devices.

Our calibration report is the most comprehensive in the industry, and we hope that the numbers arrived at do not scare you. We assure you that we use the most updated and modern equipment available to take these readings. We maintain natural standards (triple point and freeze point cells) and all of our equipment is traceable to tests performed by the NIST. A list of equipment used is printed on the calibration report, and all appropriate documentation is maintained in our Metrology Laboratory.

JMS Southeast, Inc. offers extensive testing of our sensors. The standards below may be used during testing. If certain standards are required, please specify.

Homogeneity - This is a standard test performed by JMS to verify thermoelement homogeneity.
ASTM E-207, E-220, E-230
Metallographic Examination - This special test can be performed for alloy identification.
ASTM E-235
Pressure Test - JMS can perform a special pressure test to detect or locate leaks by bubble emission techniques.
ASTM E-515
Time Response Test - JMS can measure the specified response-time characteristic of a sensor.
ASTM E-644
Helium Leak Test - The Mass Spectrometer Method can be used to determine sheath integrity.
ASTM E-908, E-839
Drift Test - A Drift Test can be performed to determine the stability of a sensor. An automatic Life Cycle testing apparatus is available to test your conditions in our lab.
ASTM E-601, E-644
Water Test - JMS can perform a special test to detect leaks.
ASTM E-839
Thermal Cycle Test - Thermal Cycling can simulate operating temperature ranges.
ASTM E-235, E-644
Radiographic Inspection - This special test can be performed to determine sheath dimensions and to detect defects.
Insulation Resistance Test - This is a standard test performed at JMS to determine a resistance value of the insulation.
ASTM E-235, E-644, E-780, E-1137
Liquid Penetrant Test - This special test can be performed to detect defects.
ASTM E-235, MIL-STD-6866
Re: For a point calibration 2 points are a minimum. For a range calibration 3 points ore more are necessary for proper interpolation of results. See pages 1-2 #15 (5&6) or 3-2 #16 (5&6).

Quality Inspections
JMS Southeast, Inc. provides laboratory services for the temperature sensors we manufacture. Throughout the manufacturing process, JMS includes quality inspections. The Quality Control Department conducts the final quality control inspection on 100% of all sensors. Standard methods for manufacturing and quality control testing may include procedures in accordance with the following:

ASTM E-235 ASTM E-1137
ASTM E-574 ASTM E-1129
ASTM E-585 ASTM E-1684
ASTM E-608 ASTM E-1350
ASTM E-839 ASTM E-380
IEC 61515 IEC 60751

Our laboratory also may reference the following specifications:

ASTM E-235 ASTM E-1137
ASTM E-574 ASTM E-1129
ASTM E-585 ASTM E-1684
ASTM E-608 ASTM E-1350
ASTM E-839 NIST Monograph 175